AD8646ARMZ OverviewPackaged in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. The op amp is delivered to you in a Tube case. There is a growing number of terminations approaching the number of 8. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. A total of 8 pins are present on the instrumentation amplifier. There is an input offset voltage of 2.5mV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . As long as the supply current of the chip does not exceed 4mA, this op amp ic can operate. 116dB should remain the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 5V. Currently, linear amplifier is operating with a quiescent current of 2mA.
AD8646ARMZ Features8 Pins
supply voltage of 5V
116dB voltage gain
Output Type: Rail-to-Rail
AD8646ARMZ ApplicationsThere are a lot of Analog Devices Inc.
AD8646ARMZ Instrumentational OP Amps applications.
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
| Lifecycle Status | PRODUCTION (Last Updated: 4 weeks ago) |
| Factory Lead Time | 10 Weeks |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8646 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 5V |
| Number of Channels | 2 |
| Operating Supply Current | 4mA |
| Quiescent Current | 2mA |
| Supply Current-Max | 5mA |
| Slew Rate | 11V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 84 dB |
| Current - Input Bias | 0.3pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±1.35V~2.75V |
| Output Current per Channel | 120mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Bandwidth | 24MHz |
| Unity Gain BW-Nom | 24000 kHz |
| Voltage Gain | 116dB |
| Average Bias Current-Max (IIB) | 0.00055μA |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 600μV |
| Settling Time | 500 ns |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.000001μA |
| Programmable Power | NO |
| Input Capacitance | 6.7pF |
| Input Voltage Noise Density | 8nV/sqrt Hz |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8646ARMZ Datasheet
+8613715157867