INA333AIDRGT OverviewPackaged in a 8-WFDFN Exposed Pad case, the buffer op amp is ready to use. An op amp ic of the Instrumentation type. The op amp is delivered to you in a Tape & Reel (TR) case. The pins on this board total to 8 in total. I would like to remind you that this buffer op amp should be powered by an 5V battery. A total of 8 pins are present on the instrumentation amplifier. There is an input offset voltage of 25μV for this buffer op amp. The mounting type that is recommended for this electrical part is Surface Mount. In relation to the operating temperature of this buffer op amp, it works well at an average of -40°C~125°C . As long as the supply current of the chip does not exceed 50μA, this op amp ic can operate. During the manufacturing process, this buffer amplifier is divided into 1 circuits. One of the many advantages that this linear amplifier has, among many other things, is the fact that it outputs Rail-to-Rail signals. For packing the buffer amplifier, the TR-axis is adopted. Currently, linear amplifier is operating with a quiescent current of 50μA. It is necessary to keep in mind that this instrumentation amplifier is able to conduct a minimum voltage gain of 1. Instrumentation amplifier resistance should stay within the range of 100GOhm. A total of 3 instrumentation amplifiers are present on the device.
INA333AIDRGT Features8 Pins
supply voltage of 5V
Output Type: Rail-to-Rail
Resistance of 100GOhm
INA333AIDRGT ApplicationsThere are a lot of Texas Instruments
INA333AIDRGT Instrumentational OP Amps applications.
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-WFDFN Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 10.886217mg |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| ECCN Code | EAR99 |
| Resistance | 100GOhm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Base Part Number | INA333 |
| Pin Count | 8 |
| Output Voltage | 1.75V |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Circuits | 1 |
| Operating Supply Current | 50μA |
| Nominal Supply Current | 50μA |
| Quiescent Current | 50μA |
| Slew Rate | 0.16V/μs |
| Amplifier Type | Instrumentation |
| Common Mode Rejection Ratio | 100 dB |
| Current - Input Bias | 70pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 25μV |
| Bandwidth | 150 kHz |
| Gain Bandwidth Product | 150 kHz |
| Average Bias Current-Max (IIB) | 0.0002μA |
| Power Supply Rejection Ratio (PSRR) | 120dB |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 10μV |
| -3db Bandwidth | 0.15MHz |
| Input Offset Current-Max (IIO) | 0.0002μA |
| Voltage Gain-Min | 1 |
| Number of Amplifiers | 3 |
| Voltage Gain-Nom | 10 |
| Height | 800μm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 730μm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
+8613715157867