LT1014DDW OverviewIn the package, you will find a 16-SOIC (0.295, 7.50mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 16 terminations. A total of 16 pins are located on this board. This linear amplifier should be powered by an 15V battery. The op amp ic has an array of 16 pins on it. Op amp rates 200μV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at 0°C~70°C , which is a good operating temperature. Using an 350μA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 120dB for the time being. On the buffer amps, there are 4 channels that can be used. The operating supply voltage of the buffer op amp is rated at 22V.
LT1014DDW Features16 Pins
supply voltage of 15V
120dB voltage gain
LT1014DDW ApplicationsThere are a lot of Texas Instruments
LT1014DDW Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Factory Lead Time | 6 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tube |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | LT1014 |
| Pin Count | 16 |
| Operating Supply Voltage | 22V |
| Number of Channels | 4 |
| Operating Supply Current | 350μA |
| Nominal Supply Current | 2.2mA |
| Power Dissipation | 1.025W |
| Slew Rate | 0.4V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 97 dB |
| Current - Input Bias | 12nA |
| Voltage - Supply, Single/Dual (±) | 4V~44V ±2V~22V |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 1MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 700 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.03μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | NO |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.05μA |
| Programmable Power | NO |
| Dual Supply Voltage | 15V |
| Input Offset Current-Max (IIO) | 0.002μA |
| Height | 2.65mm |
| Length | 10.3mm |
| Width | 7.5mm |
| Thickness | 2.35mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
LT1014DDW Datasheet
+8613715157867