OP282GSZ-REEL OverviewIn order to protect the op amps, a 8-SOIC (0.154, 3.90mm Width) case is used. There are two types of operational amplifiers in this circuit. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 8. It consists of a total of 8 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. It has 8 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 3mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~90°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 500μA and 10 . Maintain 86.02dB as the voltage gain. Buffer op amp is equipped with 2 channels on the device. As a result of this, the buffer amplifier is packed in TAPE AND REEL. There is an 250μA quiescent current in linear amplifier.
OP282GSZ-REEL Features8 Pins
supply voltage of 15V
86.02dB voltage gain
OP282GSZ-REEL ApplicationsThere are a lot of Analog Devices Inc.
OP282GSZ-REEL Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Factory Lead Time | 8 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~90°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | OP282 |
| Pin Count | 8 |
| Number of Channels | 2 |
| Operating Supply Current | 500μA |
| Max Supply Current | 500μA |
| Quiescent Current | 250μA |
| Slew Rate | 9V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | 9V~36V ±4.5V~18V |
| Output Current per Channel | 12mA |
| Input Offset Voltage (Vos) | 3mV |
| Gain Bandwidth Product | 4MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 4000 kHz |
| Voltage Gain | 86.02dB |
| Average Bias Current-Max (IIB) | 0.0005μA |
| Power Supply Rejection Ratio (PSRR) | 92dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 200μV |
| Settling Time | 1.6 μs |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.0001μA |
| Dual Supply Voltage | 5V |
| Input Voltage Noise Density | 36nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
OP282GSZ-REEL Datasheet
+8613715157867