Op amp is packaged in 8-SOIC (0.154, 3.90mm Width) case.  Op amps are General Purpose types of amplifier on the chip.  Linear amplifier is delivered in a Tape & Reel (TR) case. The number of terminations approaches 8. A total of 8 pins are located on this board. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 15V. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. 8 pins are located on the operational amplifiers. Regarding input offset voltage, op amp rates 200μV. This electronic component is recommended to be mounted using the mounting type Surface Mount. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~85°C . A supply current of 3.7mA can be used to operate this linear amplifier. You should keep the voltage gain at 160dB for the time being.  There are 1 elements in total in this linear amplifier. This linear amplifier pack is based on the TR axis.

8 Pins
supply voltage of 15V
160dB voltage gain

There are a lot of Texas Instruments OPA227UA/2K5 Instrumentational OP Amps applications.

• Comparator

  
  

• Hand-held batteries

  
  

• Addition operation circuits

  
  

• Laptop

  
  

• Micro signal measurement

  
  

• Integrator circuits

  
  

• High gain DC amplifier

  
  

• Tablets

  
  

• Professional videography

  
  

• Proportional counter tubes

  
  

  
  

  
  

  Lifecycle Status	ACTIVE (Last Updated: 1 day ago)
  Factory Lead Time	6 Weeks
  Contact Plating	Gold
  Package / Case	8-SOIC (0.154, 3.90mm Width)
  Surface Mount	YES
  Mounting Type	Surface Mount
  Number of Pins	8
  Operating Temperature	-40°C~85°C
  Packaging	Tape & Reel (TR)
  JESD-609 Code	e4
  Pbfree Code	yes
  Part Status	Active
  Moisture Sensitivity Level (MSL)	3 (168 Hours)
  Number of Terminations	8
  ECCN Code	EAR99
  Packing Method	TR
  Terminal Position	DUAL
  Terminal Form	GULL WING
  Peak Reflow Temperature (Cel)	260
  Number of Functions	1
  Supply Voltage	15V
  Base Part Number	OPA227
  Pin Count	8
  Number of Elements	1
  Operating Supply Current	3.7mA
  Nominal Supply Current	3.8mA
  Output Current	45mA
  Slew Rate	2.3V/μs
  Architecture	VOLTAGE-FEEDBACK
  Amplifier Type	General Purpose
  Common Mode Rejection Ratio	120 dB
  Current - Input Bias	2.5nA
  Voltage - Supply, Single/Dual (±)	5V~36V ±2.5V~18V
  Output Current per Channel	45mA
  Input Offset Voltage (Vos)	200μV
  Bandwidth	8MHz
  Neg Supply Voltage-Nom (Vsup)	-15V
  Unity Gain BW-Nom	8000 kHz
  Voltage Gain	160dB
  Power Supply Rejection Ratio (PSRR)	126.02dB
  Low-Offset	YES
  Frequency Compensation	YES
  Voltage - Input Offset	10μV
  Low-Bias	NO
  Micropower	NO
  Programmable Power	NO
  Nominal Gain Bandwidth Product	8MHz
  Max I/O Voltage	200μV
  Height	1.75mm
  Length	4.9mm
  Width	3.91mm
  Thickness	1.58mm
  Radiation Hardening	No
  RoHS Status	ROHS3 Compliant
  Lead Free	Lead Free