OPA313IDCKR OverviewIn order to protect the op amps, a 5-TSSOP, SC-70-5, SOT-353 case is used. There are two types of operational amplifiers in this circuit. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 5. It consists of a total of 5 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 1.8V battery. It has 5 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 2.5mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~125°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 50μA and 10 . Maintain 110dB as the voltage gain. In total, there are 1 circuits on this buffer amplifier. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. As a whole, there are 1 elements that make up this buffer amplifier. As a result of this, the buffer amplifier is packed in TR.
OPA313IDCKR Features5 Pins
supply voltage of 1.8V
110dB voltage gain
Output Type: Rail-to-Rail
OPA313IDCKR ApplicationsThere are a lot of Texas Instruments
OPA313IDCKR Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | OPA313 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Elements | 1 |
| Number of Circuits | 1 |
| Operating Supply Current | 50μA |
| Supply Current-Max | 0.06mA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 15mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.0006μA |
| Power Supply Rejection Ratio (PSRR) | 74dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 7V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1MHz |
| Max I/O Voltage | 2.5mV |
| Wideband | NO |
| Input Voltage Noise Density | 25nV/sqrt Hz |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA313IDCKR Datasheet
+8613715157867