OPA322AIDBVT OverviewA SC-74A, SOT-753 case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. It is estimated that there will be 5 terminations in the next few months. There are a total of 5 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 5V volts. There are 5 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 2mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . An 1.6mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. There are 1 channels on the operational amplifiers. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The operating supply voltage of the buffer op amp is rated at 2.75V. The instrumentation amplifier is packed in the form of TR.
OPA322AIDBVT Features5 Pins
supply voltage of 5V
130dB voltage gain
Output Type: Rail-to-Rail
OPA322AIDBVT ApplicationsThere are a lot of Texas Instruments
OPA322AIDBVT Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
| Lifecycle Status | ACTIVE (Last Updated: 6 hours ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | OPA322 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 2.75V |
| Number of Channels | 1 |
| Operating Supply Current | 1.6mA |
| Nominal Supply Current | 1.5mA |
| Output Current | 65mA |
| Slew Rate | 10V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 90 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V ±0.9V~2.75V |
| Output Current per Channel | 65mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 20MHz |
| Unity Gain BW-Nom | 20000 kHz |
| Voltage Gain | 130dB |
| Average Bias Current-Max (IIB) | 0.0008μA |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | YES |
| Micropower | NO |
| Max Frequency | 10MHz |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 20MHz |
| Max I/O Voltage | 2mV |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA322AIDBVT Datasheet
+8613715157867