OPA4340UAG4 OverviewIn the package, you will find a 14-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the General Purpose-type. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 14 terminations. A total of 14 pins are located on this board. This linear amplifier should be powered by an 5V battery. The op amp ic has an array of 14 pins on it. Op amp rates 500μV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~85°C , which is a good operating temperature. Using an 750μA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 124dB for the time being. Buffer amplifier produces Rail-to-Rail signals, which is one of its many benefits. 4 elements make up the design of this buffer amplifier. In this case, MicroAmplifier™ represents the instrumentation amplifiers' series number.
OPA4340UAG4 Features14 Pins
supply voltage of 5V
124dB voltage gain
Output Type: Rail-to-Rail
OPA4340UAG4 ApplicationsThere are a lot of Texas Instruments
OPA4340UAG4 Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Series | MicroAmplifier™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | OPA4340 |
| Pin Count | 14 |
| Qualification Status | Not Qualified |
| Output Type | Rail-to-Rail |
| Number of Elements | 4 |
| Power Supplies | 3/5V |
| Operating Supply Current | 750μA |
| Nominal Supply Current | 3.8mA |
| Slew Rate | 6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 0.2pA |
| Voltage - Supply, Single/Dual (±) | 2.5V~5.5V |
| Output Current per Channel | 50mA |
| Input Offset Voltage (Vos) | 500μV |
| Bandwidth | 5.5MHz |
| Unity Gain BW-Nom | 5500 kHz |
| Voltage Gain | 124dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Power Supply Rejection Ratio (PSRR) | 90.46dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 5.5V |
| Voltage - Input Offset | 150μV |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00001μA |
| Programmable Power | NO |
| Max I/O Voltage | 500μV |
| Input Offset Current-Max (IIO) | 0.00001μA |
| Height | 1.75mm |
| Length | 8.65mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA4340UAG4 Datasheet
+8613715157867