OPA564AIDWDR OverviewIn order to protect the op amps, a 20-SOIC (0.295, 7.50mm Width) Exposed Pad case is used. There are two types of operational amplifiers in this circuit. In the case of Tape & Reel (TR) cases, linear amplifier will be delivered. In recent months, the number of terminations has approached 20. It consists of a total of 20 pins in total. It would be helpful if you could remember that this op amp ic should be powered by an 12V battery. It has 20 pins that make up the linear amplifier. In terms of input offset voltage, operational amplifier rates 20mV. This electronic component is recommended to be mounted using the mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. In order for this instrumentation amplifier to operate, the supply current needs to be between 39mA and 10 . Maintain 108dB as the voltage gain. As a whole, there are 1 elements that make up this buffer amplifier. The operating supply voltage of the buffer op amp is rated at 12V. As a result of this, the buffer amplifier is packed in TR.
OPA564AIDWDR Features20 Pins
supply voltage of 12V
108dB voltage gain
OPA564AIDWDR ApplicationsThere are a lot of Texas Instruments
OPA564AIDWDR Instrumentational OP Amps applications.
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) Exposed Pad |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 2 (1 Year) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 12V |
| Base Part Number | OPA564 |
| Pin Count | 20 |
| Operating Supply Voltage | 12V |
| Number of Elements | 1 |
| Operating Supply Current | 39mA |
| Nominal Supply Current | 50mA |
| Output Current | 1.5A |
| Slew Rate | 40V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 10pA |
| Voltage - Supply, Single/Dual (±) | 7V~24V ±3.5V~12V |
| Output Current per Channel | 1.5A |
| Input Offset Voltage (Vos) | 20mV |
| Neg Supply Voltage-Nom (Vsup) | -12V |
| Unity Gain BW-Nom | 17000 kHz |
| Voltage Gain | 108dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 2mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 17MHz |
| Max I/O Voltage | 20mV |
| Wideband | NO |
| Height | 2.65mm |
| Length | 12.82mm |
| Width | 7.52mm |
| Thickness | 2.35mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
OPA564AIDWDR Datasheet
+8613715157867