TL074CDT OverviewA 14-SOIC (0.154, 3.90mm Width) case is used to package the op amp. J-FET-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Cut Tape (CT) case. It is estimated that there will be 14 terminations in the next few months. There are a total of 14 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 15V volts. There are 14 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 3mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about 0°C~70°C . An 1.4mA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. There are 4 channels on the operational amplifiers. The instrumentation amplifier is packed in the form of TAPE AND REEL. The Automotive, AEC-Q100 indicates the series number of the op amp.
TL074CDT Features14 Pins
supply voltage of 15V
106.02dB voltage gain
TL074CDT ApplicationsThere are a lot of STMicroelectronics
TL074CDT Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 14 |
| Operating Temperature | 0°C~70°C |
| Packaging | Cut Tape (CT) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e3 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) - annealed |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TL074 |
| Pin Count | 14 |
| Power Supplies | +-15V |
| Number of Channels | 4 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 2.5mA |
| Power Dissipation | 680mW |
| Output Current | 40mA |
| Slew Rate | 13V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 20pA |
| Voltage - Supply, Single/Dual (±) | 6V~36V ±3V~18V |
| Output Current per Channel | 40mA |
| Input Offset Voltage (Vos) | 3mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 106.02dB |
| Average Bias Current-Max (IIB) | 0.02μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Low-Bias | YES |
| Bias Current-Max (IIB) @25C | 0.0002μA |
| Dual Supply Voltage | 9V |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.01μA |
| Height | 1.65mm |
| Length | 8.75mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL074CDT Datasheet
+8613715157867