TL3414AIPWR OverviewPackaging for the buffer amplifier is in the form of a 8-TSSOP (0.173, 4.40mm Width) case. A General Purpose-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 4mA , this buffer op amp will be able to operate. Keeping the voltage gain at 100dB is the best course of action. The buffer amp consists of 2 circuits in total. The operating supply voltage of the buffer op amp is rated at 7.5V. A TR-shaped amplifier is used to pack the buffer amps.
TL3414AIPWR Features8 Pins
supply voltage of 5V
100dB voltage gain
TL3414AIPWR ApplicationsThere are a lot of Texas Instruments
TL3414AIPWR Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TL3414 |
| Pin Count | 8 |
| Operating Supply Voltage | 7.5V |
| Power Supplies | +-1.5/+-7.5/3/15V |
| Number of Circuits | 2 |
| Operating Supply Current | 4mA |
| Nominal Supply Current | 6mA |
| Slew Rate | 1.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 300nA |
| Voltage - Supply, Single/Dual (±) | 3V~15V ±1.5V~7.5V |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 1.1MHz |
| Gain Bandwidth Product | 2MHz |
| Unity Gain BW-Nom | 1100 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.1μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 15V |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.6μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.1MHz |
| Max I/O Voltage | 5mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.1μA |
| Height | 1.2mm |
| Length | 3mm |
| Width | 4.4mm |
| Thickness | 1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TL3414AIPWR Datasheet
+8613715157867