TLC272IDR OverviewPackaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 10mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 1.4mA , this buffer op amp will be able to operate. Keeping the voltage gain at 87.23dB is the best course of action. 2 channels are available on the instrumentation amplifier. A TR-shaped amplifier is used to pack the buffer amps. The LinCMOS™ stands for the buffer op amp's serial number.
TLC272IDR Features8 Pins
supply voltage of 5V
87.23dB voltage gain
TLC272IDR ApplicationsThere are a lot of Texas Instruments
TLC272IDR Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Factory Lead Time | 8 Weeks |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Cut Tape (CT) |
| Series | LinCMOS™ |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Packing Method | TR |
| Max Power Dissipation | 725mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Base Part Number | TLC272 |
| Pin Count | 8 |
| Power Supplies | 4/16V |
| Number of Channels | 2 |
| Operating Supply Current | 1.4mA |
| Nominal Supply Current | 4mA |
| Power Dissipation | 725mW |
| Slew Rate | 5.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 0.7pA |
| Voltage - Supply, Single/Dual (±) | 4V~16V ±2V~8V |
| Output Current per Channel | 30mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1.7MHz |
| Gain Bandwidth Product | 2.2MHz |
| Unity Gain BW-Nom | 2000 kHz |
| Voltage Gain | 87.23dB |
| Average Bias Current-Max (IIB) | 0.00006μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.00006μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 1.7MHz |
| Max I/O Voltage | 10mV |
| Input Offset Current-Max (IIO) | 0.00006μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
+8613715157867