TLV2462IDGKR OverviewPackaging for the buffer amplifier is in the form of a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) case. A General Purpose-type buffer amplifier is shown here. There is a Cut Tape (CT) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 3V. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~125°C as far as operating temperature is concerned. Using a supply current of 550μA , this buffer op amp will be able to operate. Keeping the voltage gain at 109dB is the best course of action. 2 channels are available on the instrumentation amplifier. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. The operating supply voltage of the buffer op amp is rated at 3V. A TR-shaped amplifier is used to pack the buffer amps.
TLV2462IDGKR Features8 Pins
supply voltage of 3V
109dB voltage gain
Output Type: Rail-to-Rail
TLV2462IDGKR ApplicationsThere are a lot of Texas Instruments
TLV2462IDGKR Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
| Lifecycle Status | ACTIVE (Last Updated: 5 days ago) |
| Factory Lead Time | 6 Weeks |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Cut Tape (CT) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | TLV2462 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Operating Supply Voltage | 3V |
| Number of Channels | 2 |
| Operating Supply Current | 550μA |
| Nominal Supply Current | 1.3mA |
| Power Dissipation | 481mW |
| Output Current | 80mA |
| Slew Rate | 1.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 66 dB |
| Current - Input Bias | 1.3nA |
| Voltage - Supply, Single/Dual (±) | 2.7V~6V ±1.35V~3V |
| Output Current per Channel | 80mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 6.4MHz |
| Unity Gain BW-Nom | 6400 kHz |
| Voltage Gain | 109dB |
| Average Bias Current-Max (IIB) | 0.075μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Voltage - Input Offset | 500μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.014μA |
| Programmable Power | NO |
| Max I/O Voltage | 2mV |
| Input Offset Current-Max (IIO) | 0.007μA |
| Height | 1.07mm |
| Length | 3mm |
| Width | 3mm |
| Thickness | 970μm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
+8613715157867