TLV271SN1T1G OverviewPackaging for the buffer amplifier is in the form of a SOT-23-5 Thin, TSOT-23-5 case. A General Purpose-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 5 terminations have been reported in the past few weeks. Buffer amplifier has a total of 5 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 5V. An 5-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at -40°C~105°C as far as operating temperature is concerned. Using a supply current of 490μA , this buffer op amp will be able to operate. Keeping the voltage gain at 110dB is the best course of action. 1 channels are available on the instrumentation amplifier. There are more than a few advantages to using this instrumentation amplifier, one of which is that it outputs Rail-to-Rail signals. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
TLV271SN1T1G Features5 Pins
supply voltage of 5V
110dB voltage gain
Output Type: Rail-to-Rail
TLV271SN1T1G ApplicationsThere are a lot of ON Semiconductor
TLV271SN1T1G Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Factory Lead Time | 4 Weeks |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-5 Thin, TSOT-23-5 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~105°C |
| Packaging | Tape & Reel (TR) |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 200mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | TLV271 |
| Pin Count | 5 |
| Output Type | Rail-to-Rail |
| Number of Channels | 1 |
| Operating Supply Current | 490μA |
| Nominal Supply Current | 550μA |
| Power Dissipation | 200mW |
| Output Current | 13mA |
| Slew Rate | 2.6V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 58 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Halogen Free | Halogen Free |
| Output Current per Channel | 13mA |
| Input Offset Voltage (Vos) | 5mV |
| Bandwidth | 3MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 3000 kHz |
| Voltage Gain | 110dB |
| Power Supply Rejection Ratio (PSRR) | 70dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 500μV |
| Current - Output / Channel | 8mA |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Height | 1mm |
| Length | 3mm |
| Width | 1.5mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TLV271SN1T1G Datasheet
+8613715157867