AD8610BRZ OverviewIn the package, you will find a 8-SOIC (0.154, 3.90mm Width)-case to contain the op amp ic. The instrumentation amplifier in this picture is of the J-FET-type. A Tube case is used for delivering the op amp. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. This linear amplifier should be powered by an 5V battery. The op amp ic has an array of 8 pins on it. Op amp rates 100μV as input offset voltage. For this electrical component, Surface Mount is the recommended mounting type. According to the manufacturer, this buffer op amp works well at -40°C~125°C , which is a good operating temperature. Using an 3.5mA supply current, this operational amplifier ics can be operated. You should keep the voltage gain at 105.11dB for the time being. On the buffer amps, there are 1 channels that can be used. The current is quiescent at 3.5mA.
AD8610BRZ Features8 Pins
supply voltage of 5V
105.11dB voltage gain
AD8610BRZ ApplicationsThere are a lot of Analog Devices Inc.
AD8610BRZ Instrumentational OP Amps applications.
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
Weak signal detection
Signal amplification
Signal filtering
Signal operation
Video computer boards
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Factory Lead Time | 10 Weeks |
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | AD8610 |
| Pin Count | 8 |
| Number of Channels | 1 |
| Operating Supply Current | 3.5mA |
| Quiescent Current | 3.5mA |
| Supply Current-Max | 4mA |
| Slew Rate | 60V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | J-FET |
| Common Mode Rejection Ratio | 110 dB |
| Current - Input Bias | 3pA |
| Voltage - Supply, Single/Dual (±) | ±5V~13V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 100μV |
| Bandwidth | 25MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Unity Gain BW-Nom | 25000 kHz |
| Voltage Gain | 105.11dB |
| Average Bias Current-Max (IIB) | 0.0025μA |
| Power Supply Rejection Ratio (PSRR) | 110dB |
| Low-Offset | YES |
| Frequency Compensation | YES |
| Voltage - Input Offset | 45μV |
| Settling Time | 600 ns |
| Low-Bias | YES |
| Dual Supply Voltage | 9V |
| Input Capacitance | 15pF |
| Input Voltage Noise Density | 6nV/sqrt Hz |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
AD8610BRZ Datasheet
+8613715157867