TS272CDT OverviewPackaging for the buffer amplifier is in the form of a 8-SOIC (0.154, 3.90mm Width) case. A General Purpose-type buffer amplifier is shown here. There is a Tape & Reel (TR) case that is delivered with the instrumentation amplifiers. A total of 8 terminations have been reported in the past few weeks. Buffer amplifier has a total of 8 pins on it. I would like you to keep in mind that this buffer amplifier needs to be run at a voltage of 10V. An 8-pin op amp ic is included in the package. With regards to the offset voltage of the input, buffer amplifier is rated at 10mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. The buffer amplifier functions well at 0°C~70°C as far as operating temperature is concerned. Using a supply current of 1mA , this buffer op amp will be able to operate. Keeping the voltage gain at 83.52dB is the best course of action. 2 channels are available on the instrumentation amplifier. The operating supply voltage of the buffer op amp is rated at 8V. A TAPE AND REEL-shaped amplifier is used to pack the buffer amps.
TS272CDT Features8 Pins
supply voltage of 10V
83.52dB voltage gain
TS272CDT ApplicationsThere are a lot of STMicroelectronics
TS272CDT Instrumentational OP Amps applications.
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
Power control
Information processing
| Lifecycle Status | ACTIVE (Last Updated: 6 months ago) |
| Factory Lead Time | 10 Weeks |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TAPE AND REEL |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 10V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | TS272 |
| Pin Count | 8 |
| Operating Supply Voltage | 8V |
| Power Supplies | 10V |
| Number of Channels | 2 |
| Operating Supply Current | 1mA |
| Nominal Supply Current | 3mA |
| Output Current | 60mA |
| Slew Rate | 5.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 65 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 3V~16V ±1.5V~8V |
| Output Current per Channel | 45mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 3.5MHz |
| Unity Gain BW-Nom | 3500 kHz |
| Voltage Gain | 83.52dB |
| Average Bias Current-Max (IIB) | 0.00015μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 1.1mV |
| Low-Bias | YES |
| Micropower | NO |
| Programmable Power | NO |
| Power | NO |
| Length | 4.9mm |
| Height Seated (Max) | 1.75mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
TS272CDT Datasheet
+8613715157867