CY2308ZXI-1H OverviewTube-method packaging is used for clock ICs. The 16-TSSOP (0.173, 4.40mm Width) package contains this clock generator. This clock generator ic can sustain a maximum temperature of 260 during reflowing. It contains 16 terminations that can be found in frequency synthesizer. This electronic frequency generator requires a voltage of 3.3V. The input of this clock generator is designed to be LVCMOS, LVTTL. To access the full performance of the electronic component, 1 circuits are implemented. There is a maximum frequency of 133.3MHz Max with this clock-based frequency generator. Thanks to the Surface Mount, this electric component can be conveniently installed on the panel. This clock generator would require a maximum supply voltage of 3.6V. For safety reasons, this frequency synthesizer should have a voltage supply above 3V. As far as the supply voltage is concerned, clock PLL can be used with 3V~3.6V. Based on the test statistics, an ambient temperature of -40°C~85°C should be set. As the name suggests, this is a clock generator that is compatible with LVCMOS logic levels. This electronic component is usually classified as a Fanout Buffer (Distribution), Zero Delay Buffer component. The clock-generating IC is a 16-bit device designed specifically for microprocessors. You can find related electrical components to the base part number CY2308. It is possible to connect to the frequency generators via 16 pins. There is a maximum supply voltage of 3.3V that clock generator can handle. 8 signal outputs enable clock PLL to magnify output frequency as high as possible. At 0.2 ns Max, this clock generator offers low timing skew. At a frequency of 133.33MHz, frequency generator is capable of achieving high efficiency.
CY2308ZXI-1H FeaturesAvailable in the 16-TSSOP (0.173, 4.40mm Width)
Supply voltage of 3.3V
Operating supply voltage of 3.3V
CY2308ZXI-1H ApplicationsThere are a lot of Cypress Semiconductor Corp
CY2308ZXI-1H Clock Generators applications.
Automatic test equipment
Wide area power system
Digital circuits
Wireless base station for LTE, LTE-advanced
Picocells, femtocells and small cells
Sampling clocks for ADC and DAC
1 Gigabit Ethernet
10 Gigabit Ethernet
FPGA and processor clocks
Line cards used in telephone exchange
| Factory Lead Time | 6 Weeks |
| Contact Plating | Gold, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 1996 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Type | Fanout Buffer (Distribution), Zero Delay Buffer |
| Terminal Finish | Matte Tin (Sn) |
| Voltage - Supply | 3V~3.6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Frequency | 133.33MHz |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | CY2308 |
| Output | LVCMOS |
| Pin Count | 16 |
| Number of Outputs | 8 |
| Operating Supply Voltage | 3.3V |
| Supply Voltage-Max (Vsup) | 3.6V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Nominal Supply Current | 70mA |
| Frequency (Max) | 133.3MHz |
| Input | LVCMOS, LVTTL |
| Ratio - Input:Output | 1:8 |
| PLL | Yes with Bypass |
| Differential - Input:Output | No/No |
| Same Edge Skew-Max (tskwd) | 0.2 ns |
| Length | 5mm |
| Width | 4.4mm |
| REACH SVHC | No SVHC |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
CY2308ZXI-1H Datasheet
+8613715157867