TS912IYDT OverviewA 8-SOIC (0.154, 3.90mm Width) case is used to package the op amp. General Purpose-type instrumentation amplifiers are used in this application. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be 8 terminations in the next few months. There are a total of 8 pins on this op amp. It is important to remember that this op amp should be operated at a voltage of 3V volts. There are 8 pins on this chip. In terms of the input offset voltage, instrumentation amplifier rates at 10mV. It is recommended that this electronic component be mounted using the Surface Mount mounting type. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . An 400μA volt supply current is needed for this linear amplifier to operate. There should be no change in the voltage gain. On this instrumentation amplifier, there are 2 circuits that are connected together. One of the advantages of this op amp is that it outputs Rail-to-Rail signals, which is one of its many advantages. The instrumentation amplifier is packed in the form of TAPE AND REEL; TUBE. The Automotive, AEC-Q100 indicates the series number of the op amp.
TS912IYDT Features8 Pins
supply voltage of 3V
92.04dB voltage gain
Output Type: Rail-to-Rail
TS912IYDT ApplicationsThere are a lot of STMicroelectronics
TS912IYDT Instrumentational OP Amps applications.
Addition operation circuits
Subtraction operation circuits
single/dual op amp sum and difference circuits
Integrator circuits
Differentiator circuits
Logarithmic operation circuits
Exponential operation circuits
Multiplication circuits
Division circuits
Precision measurement
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Factory Lead Time | 10 Weeks |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| JESD-609 Code | e4 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Packing Method | TAPE AND REEL; TUBE |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | TS912 |
| Pin Count | 8 |
| Output Type | Rail-to-Rail |
| Power Supplies | 3/10V |
| Number of Circuits | 2 |
| Operating Supply Current | 400μA |
| Supply Current-Max | 1.4mA |
| Slew Rate | 1.3V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 60 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 2.7V~16V ±1.35V~8V |
| Output Current per Channel | 75mA |
| Input Offset Voltage (Vos) | 10mV |
| Bandwidth | 1.4MHz |
| Unity Gain BW-Nom | 800 kHz |
| Voltage Gain | 92.04dB |
| Average Bias Current-Max (IIB) | 0.0003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Low-Bias | YES |
| Micropower | YES |
| Bias Current-Max (IIB) @25C | 0.00015μA |
| Programmable Power | NO |
| Power | NO |
| Length | 4.9mm |
| Height Seated (Max) | 1.75mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
TS912IYDT Datasheet
+8613715157867